VGKL 17 páginas - ISOHEAT/SAF Wärmetechnik
Heating Tapes, SAF Wärmetechnik
LabHEAT®-Heating tapes KM-HT-BS30Highly flexible; no protection against ingress of water; protective metal briding outside (protective conductor); outer sheath in glass silk
Heating Cables, SAF Wärmetechnik
LabHEAT®-Heating cables KM-HC-GHighly flexible; no protection against ingress of water; with glass-silk braiding
Heating Mantles, SAF Wärmetechnik
LabHEAT® standard heating mantles KM-G for flask, round bottomOuter jacket in glass silk and flexible glass yarn heating element, which are adapted to the respective vessel shapes and sizes, from 500 ml with 60-mm Ø bottom outlet. Maximum heating e...
Heating Mantles, SAF Wärmetechnik
LabHEAT® high temperature heating mantles KM-GH for flasks, round bottomDesigned identical to series KM-G, but the heating element is made of heat-resistant quartz yarn for higher capacities and temperatures.Maximum heating conductor temperature 900...
Heating Mantles Accessories, SAF Wärmetechnik
Tripod KM-DFMade of stainless steel (1.4031), for higher stability of heating mantles from the series KM-G and KM-GH. The heating mantle is hereby on its four clips in the tripod suspended.Supporting ring KM-TRMade of stainless steel (1.4031), for se...
Heating Mantles, SAF Wärmetechnik
LabHEAT® metal-cased heating mantles KM-M for flasks, round bottomFlexible heater in a plastic-coated, chemical-resistant metal housing with integrated mains and heating zones switch.Max. heating element temperature 450°C. 1.5 m power supply (earth...
Heating Mantles, SAF Wärmetechnik
LabHEAT® Metal-cased heating mantles KM-ME for flasks, round bottomFlexible heater in a plastic-coated, chemical-resistant metal housing with integrated mains and heating zones switch, and additionally with integrated controller for continuous power...
Heating Mantles, SAF Wärmetechnik
LabHEAT®-Multi heating mantles KM-MPE for flasks, round bottomDesign and technology identical with series KM-ME, but with a special heater, suitable for three different flask sizes. Max. heating element temperature 450°C, 1.5 m supply cable with ea...
Heating Mantles, SAF Wärmetechnik
LabHEAT® Stirred heating mantles KM-MER for flasks, round bottomDesign and technology identical with series KM-ME, but with additional integrated magnetic stirrer for separate activation (continuously adjustable speed up to 1,600 rpm, stirring power...
Heating Mantles, SAF Wärmetechnik
LabHEAT® Stirred heating mantles KM-MEB for flasks, round bottomwith corrosion-resistant stainless steel heating bowl in a plasted-coated, chemicals-resistant metal housing with integrated mains and heating zone switch and additional integrated cont...
Heating Mantles, SAF Wärmetechnik
LabHEAT®-Serial heating units KM-R6 for flasks, round bottomPlastic-coated, chemical-resistant metal housing with six heating positions. Each heating position is seperately controlled. Max. heating element temperature 450°C. 1.5 m power supply (ear...
Support Clamp, SAF Wärmetechnik
Support clamp KM-SKAccessories for housing heating mantles and serial heating unitsFor securing a support rod up to Ø 12 mm or for integrating the housing heating mantle in support setups.
Power Regulator, SAF Wärmetechnik
LabHEAT®-Power regulator KM-L116Electromechanical, infinitely variable control of the heating capacity by built-in socketStable plastic housing (W×D×H) 65 × 120 × 55 mmSwitching power max. 2950 W (13 A), Nominal voltage 230 V AC
Temperature Controller, SAF Wärmetechnik
LabHEAT® Temperature controller KM-RX1001Microprocessor-controlled tabletop unit with stage clamp, indication of setpoint and actual values in a sturdy plastic housing (H×W×D) 75 × 205 × 140 mm, freely adjustable setting range of up to 1,200°C,...
Temperature Sensors, SAF Wärmetechnik
Suitable for temperature regulator KM-RX100 and KM-RX2000, with permanently connected compensation line, with or without diode plug.KM-TNF: NiCr-Ni, up to 400°C, flat sensor 0.4 × 15 × 400 mmKM-TNS: NiCr-Ni, up to 1200°C, rod sensor made of Incoc...